Trans-Tek 0607-0002型光学编码器、Trans-Tek 607系列360°精确反馈和显示、Trans-Tek角位移传感器ADT、高精度ADTs、高精度ADTs绝对旋转位置传感器
0607-0002型光学编码器和1005-0000型计数器显示系统在360°旋转范围内提供轴角位移的精确反馈和读数。从一个固定的或用户可设置的点，角度位置显示在不确定的轴旋转，速度高达3000转/分，与等效的BCD输出，USB输出和模拟输出。在最简单的模式下，编码器位置在0.00到359.95的范围内以0.05的增量显示。显示器和编码器单独出售，无需调整即可提供完全的准确性。
关键特征
- 显示完整的360度工作范围
- 速度达到3000转/分
- 二进制编码十进制(BCD)输出
- USB输出
- 精度为0.05，分辨率为0.05
- 模拟+/-5 VDC输出
0607-0002型光学编码器
型号0607-0002是一个旋转，增量编码器，输出1800个正交TTL信号周期和一个零参考加(Zr)每轴旋转。紧凑的尺寸，低重量，伺服和/或螺栓面安装使其易于安装，即使在空间有限的地方。
编码器的精确导向直径为安装与待监控轴同心的装置提供了参考。表面上的四个螺纹孔或圆周上的伺服槽提供了两种将主体固定到用户参考面的方法。强烈建议安装挠性联轴器，以保护编码器免受被监控轴过度错位或运动的影响。编码器电缆可以直接焊接到显示器连接器上，也可以延长。
1005-0000型计数器显示器
型号1005-0000是一个面板安装，5位数的LED显示器，激励编码器，将其输出解码为7200计数/旋转，并显示轴角位置-在0.05的增量-从最后一次复位。它还提供与显示值匹配的可锁存选通BCD输出。
紧凑的1/8 DIN外壳、后面板设置和焊接端接使其易于安装，即使空间有限。该显示器可直接安装在0.25英寸(6.35毫米)厚的面板上，也可用作台式仪器。包括所有必要的配套D-SUB连接器，编码器引线、12 VDC电源和任何其他所需的连接可以直接焊接到这些连接器上。
该仪表还包括一个模拟输出，在+/-359.95范围内提供+/-5.0 VDC，以及一个USB输出，提供显示数据和远程复位操作。
ENCODER SPECIFICATIONS
| ELECTRICAL | |
| Resolution Range | 1800 cycles per revolution (7200 counts per revolution with external 4X counting when using A and B channel outputs) |
| Light Source | LED |
| Light Sensor | Photodiode |
| Excitation | 5 VDC ±10%, 80 mA |
| Output Format | Two counts channel outputs (A and B) in phase quadrature, plus zero reference ZR; all are TTL single ended square waves with rise and fall time of one microsecond maximum into 1000 pF load |
| ZR Reference | Full cycle |
| Frequency Response | Up to 100 kHz, all channels |
| Phase Sense | Channel A leads B for CW rotation of shaft (as viewed from shaft end, looking towards body) |
| Termination | Shielded cable with #24 AWG lead wires (see diagram below for lead color vs. function) |
| MECHANICAL | |
| Shaft Loading | 10 lb axially and radially, maximum; 100,000 radians/sec2 maximum angular acceleration |
| Shaft Radial Runout | 0.001 inch (.025mm) T.I.R. |
| Bearing | R-4 shielded; 0.1 ounce-inch (7.2 gram-cm) maximum starting torque at 25°C |
| Operating Speed | 3000 RPM maximum continuous |
| Materials | 303 stainless steel shaft; aluminum pilot diameter and base; anodized aluminum cover |
| Weight | 5 ounces (142 grams) |
| ENVIRONMENTAL | |
| Temperature | -23°F to 158°F (-10°C to 70°C) Operating -31°F to 176°F (-35°C to 80°C) Storage |
| Shock | 30 G’s for 11 milliseconds maximum |
| Vibration | 50 Hz, 10 G’s for 1 hour |
| Humidity | To 98% R.H. (non-condensing) |
DIMENSIONAL DIAGRAM – ENCODER
DISPLAY COUNTER SPECIFICATIONS
| ELECTRICAL | |
| Resolution Range | 0.05 count over range -359.95 to +359.95 |
| Display Type | 0.5 inch (12.7 mm) high red LEDs; 5 digits plus ± sign and decimal point |
| Excitation | 12 VDC ±10%, 400 mA maximum |
| Signal Inputs | Accepts TTL level single-ended A, B, ZR inputs; with A and B input count is multiplied by four; the inputs pass through a single pole noise filter rolled off at 100 kHz |
| Output Signal | Latchable, TTL BCD outputs that correspond to the displayed value. Analog output ±5.0 VDC over ±359.95°. USB output providing display data. |
| Selectable Set-up Features | Closing F1 resets display to 000.00 Closing F2 enables reset at ZR Closing F3 changes sense to CCW Closing F4A/B selects range 000.00 – 359.95 |
| MECHANICAL | |
| DIMENSIONS | INCHES (mm) |
| Case Size (H x W x L) | 1.72 (44) x 3.56 (90) x 6.1 (156) |
| Front Panel (H x W x L) | 1.91 (49) x 3.80 (97) x 0.1 (3) |
| Cut Out (H x W) | 1.77 (45) x 3.62 (92) |
| Max. Panel Thickness | 0.25 (6.35) |
| Termination | Two rear panel 15-pin D-SUB connectors with solder lugs and USB-A Port |
| ENVIRONMENTAL | |
| Temperature | 32°F to 131°F (0°C to 55°C) Operating 14°F to 140°F (-10°C to 60°C) Storage |
