销售：彭慧莉18721868594(微信同号)

adamczewski elektronische messtechnik-power and energy measurement 电力和能量测量 标准化接口 模拟标准信号输出 切换和脉冲输出 功率和能量显示器 监测功能

测量和评估来自交流供电网络的所有相关测量值，包括有功、无功和视在功率、电流、电压、功率因数、相角、谐波等，以及能量计数。

标准化接口

AD-LU 20 GT

产品介绍

数字功率和能量表AD-LU 20 GT测量三相系统的所有标准值（有功、无功、视在功率、电压、电流、谐波、功率因数等），并通过以太网接口提供这些值。通过Modbus-TCP协议可以读取测量值。此外，这些测量值还显示在集成的小型WEB服务器上。通过此WEB服务器也可以对设备进行参数化。AD-LU 20 GT还配备有RS485接口。该RS485接口采用Modbus-RTU协议，主要适用于连接外部显示器（AD-MM 400），但也可用于读取数据或参数设置。电流通过前置的直接电流转换器供给，可直接测量高达20A的电流。然而，也可以随时连接用于更大电流的额外电流互感器。可以测量对称或非对称的4线网络和对称负载的3线网络。由于集成的高效宽电压范围电源，该设备在大范围供电电压下运行，并且不会产生过多的热量。

产品参数

Current-inputs (I1…I3)
Measuring ranges0 … 1 A AC; 0 … 5 A AC;
0 … 20 A AC
Max. conductor diameter4,8 mm
Voltage-inputs (L1…L3)
Measuring range50 … 253 V AC
Input resistanceCa. 950 kOhm
Ethernet-interface
Software protocolModbus-TCP
Standard-IP192.168.178.99
Network mask255.255.255.0
WEB-ServerPort 80
RS485-Bus
Software protocolModbus-RTU
Data format19200, e, 8, 1
Max. bus users99
Bus termination120 ohms both sides at the end
Max. length of bus500 m (no stubs)
CableTwisted and shielded
Supply
Voltage range AC50 … 253 V AC, 50/60 Hz (see voltage-inputs)
Nominal voltage AC230 V AC
Power consumptionMax. 2,5 VA
Transfer behavior – in reference to the current value
Basic accuracy< 0,5 % (class 0.5)
Temperature influence80 ppm/K
Response time< 0,5 s
Housing
Dimensions (WxHxD)71x90x70 mm
Type of protectionIP 20
Connection methodScrew clamp
Terminals, wire cross section2,5 mm² flex wire / 4 mm² one wire
Bolting torque terminals0,6 Nm
Skinning length6 mm
Weight~ 180 g
Manner of fastening35 mm DIN rail 35mm
Environmental conditions
Ambient temperature-10 … 50 °C
Storage and transport-10 … 70 °C (no condensation)
EMC
Product family standardEN 61326-1 1)
Emitted interferenceEN 55011, CISPR11 Cl. B, Gr. 1
Electrical safety requirements
Product family standardEN 61010-1
Overvoltage categoryII
Pollution degree2
Safety measurementEN 61010-2-030
Measurement categoryCAT III
Galvanic isolation, test voltages
Grid side to RS485-Bus4 kV, 50 Hz (1 min.)
Grid side to control elements4 kV, 50 Hz (1 min.)
Protection circuits
InputElectrical surge protection
RS485-BusElectrical surge protection
Power supplyProtection against over-temperature, over-voltage and over-current

 

AD-LU 70 FE

产品介绍

数字电力转换器AD-LU 70 FE测量三相电网的所有值，如电流、电压、能量、有功、无功、视在功率和频率，并通过现场总线提供这些数据。因此，该设备非常适用于集成到能源管理系统中。AD-LU 70 FE由其测量电压L1供电。电流测量通过安装在背面的穿过孔的电流互感器进行。对于更高电压或电流的测量，必须使用外部变压器。

产品参数

Current inputs
Measuring ranges0 … 1/5/20 A AC
Maximum wire diameter4,8 mm²
Voltage inputs/supply
Nominal voltage230 V AC
Rated frequency50 Hz
Frequency range40 … 100 Hz
Measuring range80 … 253 V AC
Max. power consumption L14 VA
Input resistance L2, L3970 kOhm
Optocoupler outputs
Maximum switching voltage30 V DC
Maximum switching current50 mA DC
PROFINET
Ethernet2 Port Switch
Protocol specificationPROFINET IO
Default IP-address0.0.0.0
PROFIBUS
Bus termination120 ohms both sides at the end
Max. length of bus500 m (no stubs)
CableTwisted and shielded
Display
TypeTFT
Resolution320×240 Pixel
Accuracy
Class0,5
Temperature influence100 ppm/K
Housing
Dimensions (WxHxD)96x96x123 mm
Front panel cut out (bxh)92×92 mm
Protection Front/CaseIP54/IP20
Connection methodPluggable screw terminal
Terminals, wire cross section2,5 mm² flex wire / 4 mm² one wire
Weight250 g
Manner of fasteningPanel-mounting
Environmental conditions
Ambient temperature-10 … 50 °C
Storage and transport-10 … 70 °C (no condensation)
EMC
Product family standardEN 61326-1 1)
Emitted interferenceEN 55011, CISPR11 Cl. A, Gr. 1
Electrical safety requirements
Product family standardEN 61010-1
Overvoltage categoryII
Pollution degree2
Safety measurementEN 61010-2-030
Measurement categoryCAT III
Galvanic isolation, test voltages
Grid – PROFINET/PROFIBUS4 kV, 50 Hz (1 min.)
Grid – Digital outputs4 kV, 50 Hz (1 min.)

模拟标准信号输出

AD-LU 10 GT

产品介绍

数字电力测量变送器AD-LU 10 GT测量电力网络的所有量（电流、电压、能量、谐波、相角、有功功率、无功功率、视在功率等），并将这些测量值转换为一个可自由调节的模拟输出（20 mA）。此外，该设备还具有用于S0脉冲或报告限值的晶体管输出。因此，该单元非常适用于集成到能源管理系统中。可以测量单相或平衡的3线或4线系统。AD-LU 10 GT通过其测量电压L1供电。电流测量通过安装在前面的条形变压器进行。对于高电压或大电流的测量，可以随时连接外部变压器。AD-LU 10 GT可以通过集成接口使用AD-Studio进行读取和参数化。前面的LED指示运行状态。紧凑的构造类型和高性能与同时低能耗的特点使其在几乎任何应用中都可以使用。

产品参数

Input current
Measuring ranges0 … 1 A AC; 0 … 5 A AC;
0 … 20 A AC
Max. conductor diameter4,8 mm
Max. measurable harmonic40
Input voltage
Measuring range80 … 253 V AC
Input resistance> 900 kOhm
Output current
Output range0/4 … 20 mA
Max. load400 Ohm
Resolution11 Bit
Residual ripple25 µAss
Transistor output
Max. switching load30 V DC, 20 mA
Pulse length min … max50 ms … 10000 ms
Supply
Voltage range AC80 … 253 V AC, 50/60 Hz (see voltage-inputs)
Nominal voltage AC230 V AC
Power consumptionMax. 4 VA
Transfer behavior – in reference to the current value
Basic accuracy< 0,5 % (class 0.5)
Temperature influence80 ppm/K
Response time< 0,5 s
Housing
Dimensions (WxHxD)35,5x90x70 mm
Type of protectionIP 20
Connection methodScrew clamp
Terminals, wire cross section2,5 mm² flex wire / 4 mm² one wire
Bolting torque terminals0,6 Nm
Skinning length6 mm
Weight~ 150 g
Manner of fastening35 mm DIN rail 35mm
Environmental conditions
Ambient temperature-10 … 50 °C
Storage and transport-10 … 70 °C (no condensation)
EMC
Product family standardEN 61326-1 1)
Emitted interferenceEN 55011, CISPR11 Cl. A, Gr. 1
Electrical safety requirements
Product family standardEN 61010-1
Overvoltage categoryII
Pollution degree2
Safety measurementEN 61010-2-030
Measurement categoryCAT II
Galvanic isolation, test voltages
Grid side to analoge output4 kV, 50 Hz (1 min.)
Power Supply to Transistor Output4 kV, 50 Hz (1 min.)
Protection circuits
InputElectrical surge protection
Power supplyProtection against over-temperature, over-voltage and over-current
Analogue outputElectrical surge protection

 

AD-LU 650 GT

产品介绍

AD-LU 650 GT是用于采集三相电网中所有测量变量的数字测量变送器。除了基本振荡外，还可以测量电流和电压的谐波，直至第32次谐波。除了三相电流外，还可以测量中性导体中的电流。每个模拟输出可以分配给任何测量变量。每个数字输出可以分配其自己的功能，例如限值监测或用于能量计的脉冲输出。通过Modbus-RTU接口可以读取所有测量数据。通过可选的显示设备，如AD-MM 400 FE或AD-MM 500 FE，可以显示数据并在需要时配置设备。

产品参数

Voltage inputs L1, L2, L3 against N
Nominal voltage230 V AC
Maximum voltage300 V AC
Rated frequency32…50…100 Hz
Input resistance1 MOhm
Peak load600 V AC, 1s
Current inputs
Number4 (L1, L2, L3 und N)
Rated current range0 … 20 A AC
Current measurementIntegrated toroidal current transformer
Analog outputs
Number4
TypeCurrent or voltage, software configurable
D/A conversionPWM
Current outputs
Maximum output range-21 … 21 mA
Max. burden400 Ohm
Max. residual ripple~10 µA eff
Resolution~10 µA
Voltage outputs
Maximum output range-10,5 … 10,5 V
Min. burden10 kOhm
Max. residual ripple~5 mV eff
Resolution~5 mV
Digital outputs
Number3
TypeOptisch, MOS-Relais
Maximum switching voltage60 V AC/DC
Maximum switching current550 mA AC/DC
Accuracy
Accuracy class0,5%
Temperature influence< 200 ppm/K
Frequency influence~0,2 %, 40 … 60 Hz
Influence of phase angle~0,2 %, 40 … 60 Hz
Response time~500 ms, 10 … 90 %
Current resolution1 mA eff
Voltage resolution10 mV eff
Communication interface
PhysicalRS-485
Parameter19200, 8, 1 , even
ProtocolModbus RTU
Supply
DC21 … 253 V DC, 3,5 W
AC50 … 253 V AC, 6 VA
Housing
Type of protectionIP 20
Connection methodScrew clamp
Cross section fine wire2,5 mm2
Cross section one wire4 mm2
MountingDIN rail mounting
Weight~400 g
Environmental conditions
Operating temperature-10 … 50 °C
Storage, transport-25 … 80 °C
Electromagnetic compatibility
Product family standardEN 61326-1
EmissionEN 55011, CISPR11 Cl. B, Gr. 1
During an interference effect slight signal deviations are possible.
Electrical safety requirements
Product family standardEN 60688
Overvoltage categoryIII
Pollution degree2
Isolation-voltage500 V AC
Test voltage input/output5 kV RMS, 1 Min.
Test voltage output/supply4 kV RMS, 1 Min.
Test voltage input/supply5 kV RMS, 1 Min.

切换和脉冲输出

AD-LU 60 FE

产品介绍

AD-LU 60 FE是一款前面板安装的测量和指示设备。它涵盖了带有中性导体的三相电网中的所有测量值。电流测量是通过设备上的套管式电流互感器进行的。测量值显示在彩色的图形TFT显示器上，并分配给不同的指示器。可以手动翻阅或通过时间控制的自动方式进行。有一个基本变体作为纯指示设备，以及带有Modbus接口和用于计数或限值的数字输出的变体。设备参数设置可以通过设备本身的菜单或可选的RS-485接口进行。

产品参数

Current inputs
Measuring ranges0 … 1/5/20 A AC
Maximum wire diameter4,8 mm²
Voltage inputs/supply
Nominal voltage230 V AC
Rated frequency50 Hz
Frequency range40 … 100 Hz
Measuring range80 … 253 V AC
Max. power consumption4 VA
RS485 interface (-B, -DB)
Software protocolModbus-RTU
Data format19200, e, 8, 1
Max. bus users32
Max. length of bus500 m (no stubs)
CableTwisted and shielded
Optocoupler outputs (-D, -DB)
Max switching voltage, switching current30 V DC, 50 mA DC
Display
TypeTFT
Resolution320×240 Pixel
Accuracy
Class0,5
Temperature influence100 ppm/K
Housing
Dimensions (WxHxD)96x96x64 mm
Front panel cut out (bxh)92×92 mm
Dimensions frontIP 54
Type of protection housingIP 20
Connection methodScrew clamp
Terminals, wire cross section2,5 mm² flex wire / 4 mm² one wire
Weight250 g
Manner of fasteningPanel-mounting
Environmental conditions
Ambient temperature-10 … 50 °C
Storage and transport-10 … 70 °C (no condensation)
EMC
Product family standardEN 61326-1 1)
Emitted interferenceEN 55011, CISPR11 Cl. B, Gr. 1
Electrical safety requirements
Product family standardEN 61010-1
Overvoltage categoryII
Pollution degree2
Safety measurementEN 61010-2-030
Measurement categoryCAT III
Galvanic isolation, test voltages
Grid side to RS485-Bus4 kV, 50 Hz (1 min.)
Grid side to control elements4 kV, 50 Hz (1 min.)
Protection circuits
Voltage inputsPTC resistor
RS485-BusElectrical surge protection
Optocoupler outputsElectrical surge protection

 

AD-LU 655 GT

产品介绍

AD-LU 655 GT是一款数字测量变送器，用于获取三相电网中的所有测量变量。电流通过外部折叠式电流互感器进行检测。除了基本振荡外，该设备还可以测量电流和电压的谐波，直至第32次谐波。除了三相电流外，还可以测量中性导体中的电流。任何测量变量都可以分配给每个模拟输出。每个数字输出都可以分配其独特的功能，例如限值监测或用于能量计的脉冲输出。通过Modbus-RTU接口可以读取所有测量数据。通过可选的显示设备，如AD-MM 400 FE或AD-MM 500 FE，可以显示数据并在需要时配置设备。

产品参数

Voltage inputs L1, L2, L3 against N
Nominal voltage230 V AC
Maximum voltage300 V AC
Input resistance1 MOhm
Peak load600 V AC, 1s
Current inputs
Number4 (L1, L2, L3 und N)
Rated current range0 … 33,3 mA AC
Current measurementExterne Klappstromwandler
Input resistance~10 Ohm
Analog outputs
Number4
TypeCurrent or voltage, software configurable
Current outputs
Maximum output range-21 … 21 mA
Max. burden400 Ohm
Max. residual ripple40 µAss
Voltage outputs
Maximum output range-10,5 … 10,5 V
Min. burden10 kOhm
Max. residual ripple20 mVss
Digital outputs
Number3
TypeOptisch, MOS-Relais
Maximum switching voltage60 V AC/DC
Maximum switching current550 mA AC/DC
Accuracy
Accuracy class0,5%
Temperature influence< 200 ppm/K
Frequency influence~0,2 %, 40 … 60 Hz
Influence of phase angle~0,2 %, 40 … 60 Hz
Response time~500 ms, 10 … 90 %
Communication interface
PhysicalRS-485
Parameter19200, 8, 1 , even
ProtocolModbus RTU
Supply
DC21 … 253 V DC, 3,5 W
AC50 … 253 V AC, 6 VA
Housing
Type of protectionIP 20
Connection methodScrew clamp
Cross section fine wire2,5 mm2
Cross section one wire4 mm2
MountingDIN rail mounting
Weight~400 g
Environmental conditions
Operating temperature-10 … 50 °C
Storage, transport-25 … 80 °C
Electromagnetic compatibility
Product family standardEN 61326-1
EmissionEN 55011, CISPR11 Cl. B, Gr. 1
During an interference effect slight signal deviations are possible.
Electrical safety requirements
Product family standardEN 60688
Overvoltage categoryIII
Pollution degree2
Isolation-voltage500 V AC
Test voltage input/output5 kV RMS, 1 Min.
Test voltage output/supply4 kV RMS, 1 Min.
Test voltage input/supply5 kV RMS, 1 Min.

功率和能量显示器

AD-LU 70 FE

产品介绍

数字电力转换器AD-LU 70 FE测量三相电网的所有值，如电流、电压、能量、有功、无功、视在功率和频率，并通过现场总线提供这些数据。因此，该设备非常适用于集成到能源管理系统中。AD-LU 70 FE由其测量电压L1供电。电流测量通过安装在背面的穿过孔的电流互感器进行。对于更高电压或电流的测量，必须使用外部变压器。

产品参数

Current inputs
Measuring ranges0 … 1/5/20 A AC
Maximum wire diameter4,8 mm²
Voltage inputs/supply
Nominal voltage230 V AC
Rated frequency50 Hz
Frequency range40 … 100 Hz
Measuring range80 … 253 V AC
Max. power consumption L14 VA
Input resistance L2, L3970 kOhm
Optocoupler outputs
Maximum switching voltage30 V DC
Maximum switching current50 mA DC
PROFINET
Ethernet2 Port Switch
Protocol specificationPROFINET IO
Default IP-address0.0.0.0
PROFIBUS
Bus termination120 ohms both sides at the end
Max. length of bus500 m (no stubs)
CableTwisted and shielded
Display
TypeTFT
Resolution320×240 Pixel
Accuracy
Class0,5
Temperature influence100 ppm/K
Housing
Dimensions (WxHxD)96x96x123 mm
Front panel cut out (bxh)92×92 mm
Protection Front/CaseIP54/IP20
Connection methodPluggable screw terminal
Terminals, wire cross section2,5 mm² flex wire / 4 mm² one wire
Weight250 g
Manner of fasteningPanel-mounting
Environmental conditions
Ambient temperature-10 … 50 °C
Storage and transport-10 … 70 °C (no condensation)
EMC
Product family standardEN 61326-1 1)
Emitted interferenceEN 55011, CISPR11 Cl. A, Gr. 1
Electrical safety requirements
Product family standardEN 61010-1
Overvoltage categoryII
Pollution degree2
Safety measurementEN 61010-2-030
Measurement categoryCAT III
Galvanic isolation, test voltages
Grid – PROFINET/PROFIBUS4 kV, 50 Hz (1 min.)
Grid – Digital outputs4 kV, 50 Hz (1 min.)

监测功能

AD-UW 60 GT

产品介绍

三相电压监测器AD-UW 60 GT监测三相系统中的所有三相电压，用于过压、欠压、相序和相称。如果发生一个或多个故障，静态电流继电器将失效。通过LED指示器显示三相的状态和错误状态。该设备由测量电压供电，因此不需要单独供电线路。过压、欠压和切换延迟的触发点可以通过单独的微调器快速设置。

产品参数

Voltage inputs/supply
Nominal voltage230 V AC, 50 Hz
Connection method3 phases + neutral conductor
Auxiliary voltageAll three phases
Measurement and supply range150 … 253 V AC
Max. power consumption4 VA
Setting ranges
Undervoltage170 … 229 V AC
Overvoltage231 … 250 V AC
Delay0,1 … 10 s
Response values
Asymmetry10 % of nominal voltage
Hysteresis10 % overvoltage – undervoltage
Phase loss~ 10 % der Nennspannung
Timing
Start delay1 s
Sampling period50 ms
Notifications
L1, L2, L3 (green)On: Voltage OK
Blinking: Error, Delay is running
Off: Error
Relais (orange)On: Relay tightened, everything OK
Blinking: Relay dropped, error
Relay output
Maximum switching load AC250 V, 2 A
Maximum switching load DC50 V, 2 A
Contact constructionPotential-free changeover
Galvanic isolation, test voltages
Mains side to relay output4 kV, 50 Hz (1 min.)
Housing
Terminals, wire cross section2,5 mm² flex wire / 4 mm² one wire
Type of protectionIP 20
Connection methodScrew clamp
Bolting torque terminals0,6 Nm
Weight~ 150 g
Manner of fastening35 mm DIN rail 35mm
Environmental conditions
Ambient temperature-10 … 50 °C
Storage and transport-10 … 70 °C (no condensation)
Electrical safety requirements
Product family standardEN 61010-1
Overvoltage categoryIII
Pollution degree2
Safety measurementEN 61010-2-030
Measurement categoryCAT III
EMC
Product family standardEN 61326-1 1)
Emitted interferenceEN 55011, CISPR11 Cl. A 2), Gr. 1

 

AD-LW 110 GS

产品介绍

AD-LW 110 GS监测感性负载的负载状况。其主要应用是在1相或3相网络中负载发生较大变化的异步电动机。该设备对功率因数值和欠压进行评估。超过设定的限值将触发一个触点。通过LED在前面板上指示开关状态。功率因数的测量原理基于对一个相位中电压和电流之间的相位移的评估。因此，实际测量的变量是电压和电流之间的相位角。功率因数或相位角的设定值仅对正弦量正确。相移几乎与负载相反。因此，cos-phi值为0（= 90°）对应于低负载，而cos-phi值为1（= 0°）对应于大负载。可以将外部电流互感器连接到设备的电流输入。由于集成的高效开关电源，该设备可以在广泛的供电电压范围内运行。

产品参数

Current input (L1)
Measuring range0 … 1/5 A AC (alternatively)
Permanent overload50 %
Short-term overload 3 s100 %
Voltage input (L1, L2, L3)
Measuring range180 … 253 V
Input resistance1 MOhm
Relay outputs
Maximum switching load AC230 V, 1 A
Maximum switching load DC50 V, 1 A
Contact constructionClosing contact
Switching operations mechanical10000000
At 230V/1 A AC, cos(phi)=1600000
At 230V/1 A AC, cos(phi)=0,4200000
At 24V/1 A DC200000
Switching hysteresis3 % of the measuring range
Supply
Voltage range AC50 … 253 V AC, 50/60 Hz
Nominal voltage AC230 V AC
Voltage range DC20 … 253 V DC
Nominal voltage DC24 V DC
Power consumption AC / DC4 VA / 2,5 W
Transmission behaviour
Basic accuracy< 2 %
Temperature influence100 ppm/K
Response time~ 50 ms
Housing
Dimensions (WxHxD)23x78x103 mm
Type of protectionIP 20
Connection methodDetachable terminal clamp
Terminals, wire cross section2,5 mm² flex wire / 4 mm² one wire
Bolting torque terminals0,5 Nm
Weight~ 120 g
Manner of fastening35 mm DIN rail 35mm
Environmental conditions
Ambient temperature-10 … 50 °C
Storage and transport-10 … 70 °C (no condensation)
EMC
Product family standardEN 61326-1 1)
Emitted interferenceEN 55011, CISPR11 Cl. B, Gr. 1
Electrical safety requirements
Product family standardEN 61010-1
Overvoltage categoryII
Pollution degree2
Galvanic isolation, test voltages
Input / relay output4 kV, 50 Hz (1 min.)
Power supply / relay output4 kV, 50 Hz (1 min.)
Relay 1 / relay 22 kV, 50 Hz (1 min.)
Protection circuits
InputElectrical surge protection
Power supplyElectrical surge protection

adamczewski elektronische messtechnik-power and energy measurement 切换和脉冲输出 功率和能量显示器 标准化接口 模拟标准信号输出 电力和能量测量 监测功能

Related posts