adamczewski elektronische messtechnik- FIELDBUS DEVICES 现场总线设备在总线上的模拟标准信号输入总线上的数字输入总线上的温度信号总线到模拟标准信号输出总线到切换输出总线转换器

将模拟和数字输入输出信号转换为RS485总线技术（差分双线总线），采用Modbus RTU协议。

在总线上的模拟标准信号输入

AD-AEB 20 GX

产品介绍 AD-AEB 20 GX实现了2通道模拟信号采集，同时提供经过数字处理的过程变量。信号通过RS485总线接口提供。可以通过实现的MODBUS命令调用模拟值和缩放值。有关缩放或滤波器的所有设置均通过MODBUS命令进行。电源和RS485总线连接可以通过后方的DIN导轨连接器进行。该设备配备有两个旋转编码开关，可用于在设备上设置总线地址。读取电流值时，输入电流电阻会自动开启。通过输入信号开关（E1 / E2），可以将每个信号输入永久连接到50欧姆的终端电阻，以便在供电电压失败时安全地完成电流回路。 产品参数

Current inputs
Measuring range	0 ... 20 mA
Input resistance	50 Ohm
Voltage inputs
Measuring range	0 ... 10 V
Input resistance	100 kOhm
Signal detection
Channel counts (U/I)	2
Basic accuracy	< +/- 0,3 %
Temperature influence	80 ppm/K
Sampling rate / resolution	100 ms / 10 bit
Transmission behaviour
Response time	Max. 15 ms
RS485-Bus
Software protocol	Modbus-RTU
Data format	19200, e, 8, 1
Max. bus users	99
Bus termination	120 ohms both sides at the end
Max. length of bus	500 m (no spur lines)
Cable	Twisted and shielded
Supply
Supply voltage	18 ... 30 V DC
Max. power consumption	600 mW (24V DC)
Housing
Dimensions (WxHxD)	6,2 x 92 x 101 mm³
Manner of fastening	DIN rail mounting 35mm, EN 50022
Type of protection	IP 20
Connection method	Screw clamp
Bolting torque terminals	0,5 Nm
Wire cross section	Max. 2,5 mm²
Weight	~ 70 g
Environmental conditions
Permissible ambient temperature	-10 ... +50 °C
Storage and transport	-10 ... +70 °C (no condensation)
EMC
Product family standard ¹⁾	EN 613261
Emission ²⁾	EN 55011, CISPR11 Cl. A, Gr. 1
¹⁾ During checking, slight signal deviations are possible.
²⁾ Warning: This device is not intended to be used in residential areas and can not ensure adequate protection of radio reception in such environments.
Electrical safety requirements
Product family standard	EN 61010-1
Galvanic isolation, test voltages
RS485 bus / power supply	1,5 kV, 50 Hz (1 min)
Analog inputs / power supply	1.5 kV, 50 Hz (1 min)
Analog input / RS485 bus	1,5 kV, 50 Hz (1 min)
Analog inputs between themselves	0 kV
Protection circuits
Power supply	Electrical surge and reverse current protection

AD AEB 40 GT

产品介绍 AD AEB 40 GT实现了4通道模拟信号采集，同时提供经过数字处理的过程变量。信号通过可用的RS485总线接口提供。可以通过实现的MODBUS命令获取模拟值和缩放值。所有关于缩放或滤波器的设置都通过MODBUS命令进行。工作电压由绿色LED指示。数据通信由黄色LED指示。检测到超出定义的测量范围的无效测量信号时，绿色LED会闪烁。 产品参数

Current inputs
Measuring range	0 ... 20 mA
Input resistance	50 Ohm
Voltage inputs
Measuring range	0 ... 10 V
Input resistance	100 kOhm
Signal detection
Channel counts (U/I)	4
Basic accuracy	< 0,2 %
Temperature influence	80 ppm/K
Sampling rate / resolution	100 ms / 11 bit
RS485-Bus
Software protocol	Modbus-RTU
Data format	19200, e, 8, 1
Max. bus users	99
Bus termination	120 ohms both sides at the end
Max. length of bus	500 m (no stubs)
Cable	Twisted and shielded
Supply
Voltage range AC	50 ... 253 V AC, 50/60 Hz
Nominal voltage AC	230 V AC
Power consumption	Max. 1,5 VA
Voltage range DC	20 ... 253 V DC
Nominal voltage DC	24 V DC
Power consumption	Max. 0,5 W
Housing
Dimensions (WxHxD)	71 x 90 x 58 mm
Type of protection	IP 20
Connection method	Screw clamp
Terminals, wire cross section	2,5 mm² flex wire / 4 mm² one wire
Bolting torque terminals	0,6 Nm
Skinning length	6 mm
Weight	~ 140 g
Manner of fastening	35 mm DIN rail 35mm
Environmental conditions
Ambient temperature	-10 ... 50 °C
Storage and transport	-10 ... 70 °C (no condensation)
EMC
Product family standard	EN 61326-1 ¹⁾
Emitted interference	EN 55011, CISPR11 Cl. B, Gr. 1
Electrical safety requirements
Product family standard	EN 61010-1
Overvoltage category	II
Pollution degree	2
Galvanic isolation, test voltages
Grid side to RS485-Bus	3 kV, 50 Hz (1 min.)
Signal / supply unit	3 kV, 50 Hz (1 min.)
Signal / RS485 bus	1 kV, 50 Hz (1 min.)
Protection circuits
Input	Electrical surge protection
RS485-Bus	Electrical surge protection
Power supply	Electrical surge protection

总线上的数字输入

AD-KEB 20 GX

产品介绍 两通道的AD-KEB 20 GX用于读取以触点或主动24V信号形式存在的数字信号。通过红色LED在设备上指示相应的信号状态。设备通信通过RS485总线接口进行，并使用MODBUS RTU协议实现。电源和RS485总线连接可以通过后方的DIN导轨连接器进行。该设备配备有两个旋转编码开关，可用于在设备上设置总线地址。光学搜索功能允许在网络中定位单个设备。为此，绿色LED在限定时间内以闪烁模式设置，时间范围为1到255秒。界面设置以及设备地址可以通过Modbus命令在操作过程中进行修改。所有Modbus寄存器地址及其相关命令都列在文档附件中。可预设的绝对计数器不断累加传入的脉冲，并每小时保存在非易失性存储器中。在读数期间，当前计数器会重置以检测子集。 产品参数

Input
Input voltage	24 V DC / 3,5 mA (max. 30V)
Switching threshold	~ 17 V
Contact load	5 V / 1,5 mA
Measure
Frequency	< 2200 Hz
Gate time	1 s
Accuracy	+/- 0,3%
Counter	0...4294967295
Pulse width (counter)	> 25 ms
Counting frequency	< 20 Hz
Contact debouncing	20 ms
Counter storage	Stündlich
Transmission behaviour
Response time	Max. 15 ms
RS485-Bus
Software protocol	Modbus-RTU
Data format	19200, e, 8, 1
Max. bus users	99
Bus termination	120 ohms both sides at the end
Max. length of bus	500 m (no spur lines)
Cable	Twisted and shielded
Supply
Supply voltage	18 ... 30 V DC
Max. power consumption	800 mW (24V DC)
Housing
Dimensions (WxHxD)	6,2 x 92 x 101 mm³
Manner of fastening	DIN rail mounting 35mm, EN 50022
Type of protection	IP 20
Connection method	Screw clamp
Bolting torque terminals	0,5 Nm
Wire cross section	Max. 2,5 mm²
Weight	~ 70 g
Environmental conditions
Permissible ambient temperature	-10 ... +50 °C
Storage and transport	-10 ... +70 °C (no condensation)
EMC
Product family standard ¹⁾	EN 61326-1
Emission ²⁾	EN 55011, CISPR11 Cl. A, Gr. 1
¹⁾ During checking, slight signal deviations are possible.
²⁾ Warning: This device is not intended to be used in residential areas and can not ensure adequate protection of radio reception in such environments.
Electrical safety requirements
Product family standard	EN 61010-1
Galvanic isolation, test voltages
RS485 bus / power supply	1,5 kV, 50 Hz (1 min)
Digital input / Power supply	1.5 kV, 50 Hz (1 min)
Digital input / RS485 bus	1,5 kV, 50 Hz (1 min)
Digital input between themselves	0 kV
Protection circuits
RS485-Bus	Electrical surge protection
Power supply	Electrical surge and reverse current protection

总线上的温度信号

AD-MV 554 GT

产品介绍 4通道变送器AD-MV 554 GT是一款可编程的测量设备，用于测量电阻和毫伏信号。由于集成了功能块和自由线性化曲线，AD-MV 554 GT可以通用使用，主要用于温度传感器的温度测量。通过Modbus RTU协议，可以通过适当的寄存器访问测量值。通过前面板可访问的地址开关，可以设置1到99的设备地址。所有参数都通过RS485接口使用“AD-Studio” PC配置软件进行设置。接口参数也可以设置用于将设备插入现有总线系统中。工作电压由绿色发光二极管指示。数据通信由黄色发光二极管表示。检测到超出定义的测量范围的无效测量信号时，绿色LED会闪烁。 产品参数

Resistance thermometer inputs Pt100, Pt500, Pt1000 to DIN EN 60751
Measuring range	-200 ... +850 °C
Connection method	2-, 3-, 4-wire system
Resolution	16 Bit
Accuracy	2 K
Smallest measuring spans	30 K
Max line resistance ¹⁾	10 Ohm / cable
Sensor supply
For 4-wire connection	< 500 µA
For 2 - and 3-wire connection	< 250 µA
¹⁾ With 2-conductor the line resistance comes as an offset into the measurement.
Resistance thermometer inputs Ni100, Ni500, Ni1000 to DIN EN 43760
Measuring range	-60 ... +230 °C
Connection method	2-, 3-, 4-wire system
Resolution	16 Bit
Accuracy	2 K
Smallest measuring spans	30 K
Max line resistance ¹⁾	10 Ohm / cable
Sensor supply
For 4-wire connection	< 500 µA
For 2 - and 3-wire connection	< 250 µA
¹⁾ With 2-conductor the line resistance comes as an offset into the measurement.
Thermocouples
Comparative place:
Internal	Measurement at device terminals
External	Cold junction temperatureselectable by parameters
Resolution	16 Bit
Accuracy	0,2 % of measuring range
Measuring range type J	-200 ... +1200 °C
To DIN EN 60584:
Measuring range type T	-200 ... +400 °C
Measuring range type K	-200 ... +1360 °C
Measuring range type E	-200 ... +1000 °C
Measuring range type N	-200 ... +1300 °C
Measuring range type S	-40 ... +1760 °C
Measuring range type R	-40 ... +1760 °C
Measuring range type B	+400 ... +1800 °C
After standard ASTM E988:
Measuring range type C	0 ... +2320 °C
Smallest measuring spans	100 K
Voltage inputs
Measuring range	-18 ... +18 mV
	-36 ... +36 mV
	-72 ... +72 mV
	-144 ... +144 mV
Resolution	16 Bit
Accuracy	0,2 % of measuring range
Transmission behaviour
Sampling rate	1 measure / s
Temperature influence	+/- 100 ppm / K of full scale
RS485-Bus
Software protocol	Modbus-RTU
Data format	19200, e, 8, 1
Max. bus users	99
Bus termination	120 ohms both sides at the end
Max. length of bus	500 m (no spur lines)
Cable	Twisted and shielded
LEDs
Green [On]	Supply (blinking on error)
Yellow [DATA]	RS485 Communication
Controls
Address switch	01 ... 99
Supply
Supply voltage	20 ... 253 V DC / 50 ... 253 V AC
Max. power consumption	0,6 W / 1,4 VA
Housing
Dimensions (WxHxD)	71 x 90 x 58 mm³
Manner of fastening	DIN rail mounting 35mm, EN 50022
Type of protection	IP 20
Connection method	Screw clamp
Bolting torque terminals	0,5 Nm
Wire cross section	Max. 2,5 mm²
Weight	Ca. 30 g
Environmental conditions
Permissible ambient temperature	-10 ... +50 °C
Storage and transport	-10 ... +70 °C (no condensation)
EMC
Product family standard ²⁾	EN 61326-1
Emitted interference	EN 55011, CISPR11 Cl. B, Gr. 1
²⁾ During electromagnetic disturbance minor changes in output signal are possible.
Electrical safety requirements
Product family standard	EN 61010-1
Overvoltage category	II
Pollution degree	2
Galvanic isolation, test voltages
Signal / supply unit	3 kV, 50 Hz (1 min.)
Signal / RS485 bus	Nogalvanic isolation
Signal / Signal	Nogalvanic isolation

总线到模拟标准信号输出

AD-AAB 20 GX

产品介绍 AD-AAB 20 GX提供2通道模拟信号的输出。设备通信采用MODBUS RTU协议实现。可以通过实现的MODBUS命令设置模拟设定值。电源和RS485总线连接可以通过后方的DIN导轨连接器进行。该设备配备有两个旋转编码开关，可用于在设备上设置总线地址。工作电压由绿色LED指示。数据通信由黄色LED指示。光学搜索功能允许在网络中定位单个设备。为此，绿色LED在限定时间内以闪烁模式设置，时间范围为1到255秒。界面设置以及设备地址可以通过Modbus命令在操作过程中进行修改。所有Modbus寄存器地址及其相关命令都列在文档附件中。 产品参数

Current outputs
Range	0 ... 20 mA
Output load	Max. 450 Ohm
Voltage outputs
Range	0 ... 10 V
Output load	Min. 10 kOhm
Signal output
Channel counts (U/I)	2
Basic accuracy	< +/- 0,3 %
Temperature influence	100 ppm/K
Resolution	12 bit
Transmission behaviour
Response time	Max. 15 ms
RS485-Bus
Software protocol	Modbus-RTU
Data format	19200, e, 8, 1
Max. bus users	99
Bus termination	120 ohms both sides at the end
Max. length of bus	500 m (no spur lines)
Cable	Twisted and shielded
Supply
Supply voltage	18 ... 30 V DC
Max. power consumption	1400 mW (24V DC)
Housing
Dimensions (WxHxD)	6,2 x 92 x 101 mm³
Manner of fastening	DIN rail mounting 35mm, EN 50022
Type of protection	IP 20
Connection method	Screw clamp
Bolting torque terminals	0,5 Nm
Wire cross section	Max. 2,5 mm²
Weight	~ 70 g
Environmental conditions
Permissible ambient temperature	-10 ... +50 °C
Storage and transport	-10 ... +70 °C (no condensation)
EMC
Product family standard ¹⁾	EN 61326-1
Emission ²⁾	EN 55011, CISPR11 Cl. A, Gr. 1
¹⁾ During checking, slight signal deviations are possible.
²⁾ Warning: This device is not intended to be used in residential areas and can not ensure adequate protection of radio reception in such environments.
Electrical safety requirements
Product family standard	EN 61010-1
Galvanic isolation, test voltages
RS485 bus / power supply	1,5 kV, 50 Hz (1 min)
Analog output / power supply	1.5 kV, 50 Hz (1 min)
Analog output / RS485 bus	1,5 kV, 50 Hz (1 min)
Analog outputs between themselves	0,5 kV, 50 Hz (1 min)
Protection circuits
Power supply	Electrical surge and reverse current protection

总线到切换输出

AD-KAB10 GX

产品介绍 AD-KAB10 GX提供可远程控制的继电器切换接触（切换接触）。远程控制通过RS-485总线接口进行，设备通信采用MODBUS RTU协议。电源和RS485总线连接可以通过后方的DIN导轨连接器进行。该设备配备有两个旋转编码开关，可用于在设备上设置总线地址。静态接触控制是通过控制值0或1进行的。脉冲输出功能（1Hz）在控制值为1到255时触发，并可以随时使用其他值进行修改或停止。当在柜子中有多个设备安装在一条导轨上时，光学搜索功能允许在设备网络中定位单个设备。为此，绿色LED在限定时间内以闪烁模式设置，时间范围为1到255秒。对于继电器，可以设置定义的起始状态，以便在供电电压在停电后恢复时，系统可以假定所需的起始状态。界面设置以及设备地址可以通过Modbus命令在操作过程中进行修改。所有Modbus寄存器地址及其相关命令都列在文档附件中。 产品参数

Relay
Maximum switching load AC	250 V, 2 A
Maximum switching load DC	50 V, 2 A
Contact construction	Changeover contact
Switching operations mechanical	10000000
At 230V/2A AC, cos(phi)=1	500000
At 24V/1 A DC	1000000
Transmission behaviour
Response time	Max. 15 ms
RS485-Bus
Software protocol	Modbus-RTU
Data format	19200, e, 8, 1
Max. bus users	99
Bus termination	120 ohms both sides at the end
Max. length of bus	500 m (no spur lines)
Cable	Twisted and shielded
Supply
Supply voltage	18 ... 30 V DC
Max. power consumption	700 mW (24V DC)
Housing
Dimensions (WxHxD)	6,2 x 92 x 101 mm³
Manner of fastening	DIN rail mounting 35mm, EN 50022
Type of protection	IP 20
Connection method	Screw clamp
Bolting torque terminals	0,5 Nm
Wire cross section	Max. 2,5 mm²
Weight	~ 70 g
Environmental conditions
Permissible ambient temperature	-10 ... +50 °C
Storage and transport	-10 ... +70 °C (no condensation)
EMC
Product family standard ¹⁾	EN 61326-1
Emission ²⁾	EN 55011, CISPR11 Cl. A, Gr. 1
¹⁾ During checking, slight signal deviations are possible.

²⁾ Warning: This device is not intended to be used in residential areas and can not ensure adequate protection of radio reception in such environments.
Electrical safety requirements
Product family standard	EN 61010-1
Galvanic isolation, test voltages
RS485 bus / power supply	1,5 kV, 50 Hz (1 min)
Relay contact	3 kV, 50 Hz (1 min)
Protection circuits
RS485-Bus	Electrical surge protection
Power supply	Electrical surge and reverse current protection

AD-KAB 40 GT和AD-KAB 80 GT

产品介绍 使用RS485继电器模块AD-KAB 40 GT和AD-KAB 80 GT，可以通过RS485总线远程控制4个或8个无电位的常开触点。在RS485总线上使用的Modbus-RTU协议是一种开放标准，因此非常灵活。最多可以通过单独的Modbus寄存器对八个继电器进行个别控制。这些设备配备有两个旋转编码开关，可用于在设备上设置总线地址。如果DIP开关处于活动状态（手动操作中），则会忽略相应继电器的总线命令，因为手动操作具有优先权。由于紧凑而高效的开关电源，这些设备可以在广泛的供电电压范围内运行。 产品参数

RS485-Bus
Software protocol	Modbus-RTU
Data format (default setting)	19200, e, 8, 1
Max. bus users	99
Bus termination	120 ohms both sides at the end
Max. length of bus	500 m (no spur lines)
Cable	Twisted and shielded
Relay
Maximum switching load AC	250 V, 2 A
Maximum switching load DC	50 V, 2 A
Contact construction	Closing contact
Switching operations mechanical	10000000
At 230V/2A AC, cos(phi)=1	600000
At 230V/2A AC, cos(phi)=0,4	200000
At 24V/1 A DC	200000
Supply
Voltage range AC	50 ... 253 V AC, 50/60 Hz
Nominal voltage AC	230 V AC
Voltage range DC	22 ... 253 V DC
Nominal voltage DC	24 V DC
Power consumption AC / DC	3,5 VA / 2,5 W
Transmission behaviour
Response time	Max. 5 ms
Housing
Dimensions (WxHxD)	71x90x58 mm
Type of protection	IP 20
Connection method	Detachable terminal clamp
Terminals, wire cross section	2,5 mm² flex wire / 4 mm² one wire
Bolting torque terminals	0,5 Nm
Weight	~ 200 g
Manner of fastening	35 mm DIN rail 35mm
Environmental conditions
Ambient temperature	-10 ... 60 °C
Storage and transport	-10 ... 70 °C (no condensation)
EMC
Product family standard	EN 61326-1 ¹⁾
Emitted interference	EN 55011, CISPR11 Cl. B, Gr. 1
Electrical safety requirements
Product family standard	EN 61010-1
Overvoltage category	II
Pollution degree	2
Galvanic isolation, test voltages
Power supply / RS485-Bus	3 kV, 50 Hz (1 min.)
Power supply / relay output	3 kV, 50 Hz (1 min.)
Relay output / RS485-Bus	3 kV, 50 Hz (1 min.)
Protection circuits
RS485-Bus	Electrical surge protection
Power supply	Electrical surge and reverse current protection

总线转换器

AD-NETGW 100 GT

产品介绍 网络接口转换器（AD-NETGW 100 GT）允许通过基于IP的网络（LAN）连接到具有串行接口的设备。为此，该设备包含一个LAN连接、一个RS485接口和一个AD-UART接口。内置的宽范围电源模块使其可以在几乎所有的供电情况下运行。 产品参数

Ethernet-interface
LAN	10/100 Mbit
Protocol	TCP/IP
Addressing	IP4
DHCP	Can be deactivated
IP standard address	192.168.178.99
Access port	80
Password protection	Configuration / webserver
RS485-interface
Baud rate	2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 76800
Data format	8N1, 8E1, 8O1
Max. bus users	32
Bus termination	120 ohms both sides at the end
Max. length of bus	500 m (no stubs)
Cable	Twisted and shielded
AD-UART-interface
Baud rate	2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 76800
Data format	8N1, 8E1, 8O1
Supply
Voltage range AC	50 ... 253 V AC, 50/60 Hz
Nominal voltage AC	230 V AC
Voltage range DC	20 ... 253 V DC
Nominal voltage DC	24 V DC
Input power AC/DC	1,8 VA / 1 W
Housing
Dimensions (WxHxD)	35,5 x 90 x 58 mm
Type of protection	IP 20
Connection method	Screw clamp
Terminals, wire cross section	2,5 mm² flex wire / 4 mm² one wire
Bolting torque terminals	0,6 Nm
Skinning length	6 mm
Weight	~ 90 g
Manner of fastening	35 mm DIN rail 35mm
Environmental conditions
Ambient temperature	-10 ... 50 °C
Storage and transport	-10 ... 70 °C (no condensation)
EMC
Product family standard	EN 61326-1 ¹⁾
Emitted interference	EN 55011, CISPR11 Cl. B, Gr. 1
Electrical safety requirements
Product family standard	EN 61010-1
Overvoltage category	II
Pollution degree	2
Galvanic isolation, test voltages
Supply line to all interfaces	3 kV, 50 Hz (1 min.)
Ethernet to AD-UART/RS-485	1,5 kV, 50 Hz (1 min.)
Protection circuits
Interfaces	Electrical surge protection
Power supply	Protection against over-temperature, over-voltage and over-current

AD-VARIOCONTROL, AD-VARIOCONNECT

产品介绍 可拆卸的控制模块AD-VarioControl用于显示具有相关接口的基础设备（发射器、隔离放大器等...）的测量值。插入后（即使在基础设备运行期间也可以无限制地插入），基础设备将被自动读取，并显示相应的测量值。除了显示功能外，还可以访问基础设备的参数和控制功能。可以使用备份功能将参数设置加载到控制面板中，并在相同类型的不同基础设备上进行恢复。建立发射器通常只需要在设备的操作周期内进行一次，因此并非每个设备都需要永久性的显示和操作元素。通过将AD-VarioControl与兼容的基础设备配合使用，可以省去每个单独设备上的操作元素和显示。这样，安装的设备就是防篡改的，并且更具成本效益。 AD-VarioConnect具有通过RS485的Modbus-RTU协议的现场总线接口。通过这个接口，可以获取基本单元的所有测量值。 产品参数

Display
Type	LCD graphic
Dimensions (WxH)	18x13 mm
Resolution	42X56 Pixel
Lighting	RGB
Operation
Type	3 short-stroke keys
RS485 Bus (Varioconnect)
Protocol	Modbus-RTU
Data format (default)	19200, e, 8, 1
Max. bus users	32
Bus termination	120 ohms both sides at the end
Max. length of bus	500 m (no stubs)
Cable	Twisted and shielded
Supply
Supply voltage	5 DC
Max. power consumption	0,2 W
Housing
Dimensions (WxHxD)	20x86x14 mm
Dimensions with clamp	20x95x14 mm
Type of protection	IP 20
Weight	20 g
Environmental conditions
Ambient temperature	-10 ... 50 °C
Storage and transport	-10 ... 70 °C (no condensation)
EMC
Product family standard	EN 61326-1
Emitted interference	EN 55011, CISPR11 Cl. B, Gr. 1
Electrical safety requirements
Product family standard	EN 61010-1
Galvanic isolation, test voltages (VarioConnect)
RS485-bus to basic device	1,5 kV

询价采购adamczewski elektronische messtechnik- FIELDBUS DEVICES 现场总线设备在总线上的模拟标准信号输入总线上的数字输入总线上的温度信号总线到模拟标准信号输出总线到切换输出总线转换器

请用微信扫描下方二维码或手动添加微信号2351992198