美国 Monarch Instrument ACT-1B 面板转速表

美国 Monarch Instrument

ACT-1B 面板转速表

ACT-3X 面板转速表是一款功能强大的 NIST 校准、完全可编程的转速表和累加器。它接受来自所有 Monarch 速度传感器或任何标准 TTL 生成设备的输入。

描述

ACT-3X 面板转速表是一款功能强大的 NIST 校准、完全可编程的转速表和累加器。它接受来自所有 Monarch 速度传感器或任何标准 TTL 生成设备的输入。该装置由 120/240 V 交流输入电源或 12 或 24 V 直流输入电源（可选）供电。可通过 5 个前面板按钮或使用免费下载的 PM 远程软件轻松进行编程。设置为单通道监控。可编程比例因子，菜单选择每转多个脉冲、线性速率、单事件跳闸速度（使用辅助输入）和 RPM 变化率。TTL 脉冲中继器输出为标准配置。建议使用的传感器有 PN -W（= 镀锡引线）、ROS-W、ROS-HT-W-25、 P5-11、PS-12、 M-190W、 IRS-W、 ROLS-W 、 RLS-W、 SLS-115/230、CSLS和 GE-200HP燃气发动机传感器（带放大器）。

特征

所有型号 - 通用输入，通过光学、红外、激光、接近和磁传感器或直接 TTL 和 200 mV 至 50 V 交流信号进行非接触式操作 ACT-3X 面板转速表

1/8 DIN 尺寸
5位LED显示屏
转速范围：5 至 999,990 RPM
通用传感器输入
包含 NIST 可追溯证书
用户可使用前面板按钮或免费下载 PM 远程软件进行配置
在电脑上查看实时数据*
以 .CSV 格式实时记录数据*
通用交流电源 100-240 V 交流电，50/60 Hz 或可选 12 或 24 V 直流电源
标准脉冲中继输出
从启停脉冲中捕获单个事件，单位包括 MPH、CM/秒等使用二传感器 - 用于测量第二输入通道的线性行进速率
可选 4-20 mA 或 0-5 V dc 可扩展输出
可选以太网或 USB 通信
可选报警继电器输出

参数*


Speed Range	5-999,999 RPM (speeds below 5 RPM possible with multiple pulses per revolution)
Input Frequency Range	0.083 Hz to 80 kHz
Totalizer/Counter	Display Range: 0.001 to 99,999
Input Configuration	Universal inputs: 1 to 9,999 pulses per revolution front panel pushbutton programmable TTL input and 1.1 V to 50 V ac signals, Opt: -1 to -50 V dc
Accuracy	+/-0.001% of reading or +/-1 displayed resolution (standard gate), +/-0.06% of reading or +/-1 displayed resolution (fast gate)
Resolution	Up to 0.001 RPM, 10 RPM (100,000 to 999,990 RPM)
Display	5-digit, 0.56 in. [14 mm] high red LED
Display and Output Update	Menu-selectable between 0.5 seconds above 120 RPM, 1 second above 60 RPM, and 1.5 seconds above 40 RPM
Max Measurement Rate	Up to 100 times per second (Standard Gate) or up to 1000 (Fast Gate) dependent on the input frequency; input must be measurement rate
Scaling	Programmable scaling: 0.0001 to 9999.9 (front panel pushbutton programmable)
Decimal Point	User-selectable (0-3) decimal places max (front panel pushbutton programmable)
Memory	Maximum, minimum, and last reading recall from front panel pushbuttons
Dimensions	1/8 DIN by 4.5 in. [114 mm] deep Panel cutout: 3.58 in. x 1.74 in. [91 x 44 mm]
Input Power	Standard: 100-240 V ac +/-10%, 50/60 Hz Optional: 12 or 24 V dc +/-20%, isolated, 8VA
Inputs	Universal input for optical, proximity, two-wire or three-wire magnetic, infrared, or laser sensors; TTL input or 3.3 V ac to 50 V ac input (The standard input is 1 pulse per revolution.)
Sensor Excitation	5 V dc or optional 12 or 24 V dc to sensor
Recommended Sensors	LED - ROS-W High Temp - ROS-HT-W-25 Proximity - P5-11, PS-12 Magnetic - M-190W or MT-190W Infrared - IRS-W Laser - ROLS-W, RLS-W, SLS-115/230, CSLS Inductive - GE200-HP Gas Engine (requires amplifier)
Pulse Repeater Output	Standard, 0 to 5 V TTL compatible; one pulse out for each pulse in Menu-selectable polarity
Communications	Bidirectional RS232C, USB, or Ethernet interface
Analog Output (optional)	Voltage (AO): 0 to 5 V dc, 5 mA max load (isolated or non-isolated) or Current (IO): 4 to 20 mA, 500 ohm,¦ max load. (or non-isolated), 1 to 5 V dc possible using 250 ohm resistor) 16-bit resolution Front panel pushbutton programmable for full scale and offset RPM ranges
Pulse Output (optional)	Repeater pulse output: TTL pulse switching between +5 V and ground
Alarm Capability	Two-alarm setpoints: High or Low alarm limits, latching or non-latching Front panel pushbutton programmable Hysteresis, deadband, and low limit lockout are programmable; relays can be set as a fail-safe Alarms can be reset manually or automatically; remote reset via the auxiliary input
Alarm Outputs	Two Form C relay contacts, rated 1 A at 115 V ac or 230 V ac
Remote Programming	Remote programming is possible using an optional communications interface and PM Remote Software (If no communications are ordered, the unit can still be programmed with an optional USB programming cable.)
Environmental	Indoor use only, installation category II per IEC 664 temperature: -10 °C to 50 °C operating per IEC 61010-1 Humidity: maximum relative humidity 80% for temperatures up to 31 °C, decreasing linearly to 50% relative humidity at 40 °C
Electrical Safety	Meets EN61010-1:2001, EC low voltage directive 72/23/EEC and 89/336/EEC